• Line Shaft Driven - Accumulation Conveyor

    • Zero pressure accumulation
    • Clean room installation
    • Clean room installation
    • Easy installation
    • True product singulation
    • No mechanical sensor roller
    • Photo eye controlled

    Driving belts – 3/16" diameter urethane "O" rings from drive shaft to rollers.
    Bed – 7" x 1 1/2" x 12 gauge powder painted formed steel channel frame with heavy duty cross braces and splice plates.
    Rollers – 1.9" diameter x 16 gauge galvanized steel tread rollers with 7/16" hex shaft and sealed, greased for life bearings, spaced on 3" centers.
    Sensing device – NEMA 1 photoelectric sensor in each zone detects presence of product and activates accumulation feature in the trailing zone if upstream zone is occupied.
    Power supply – 120 VAC power supply controls accumulation feature with 24 VDC output. Power supply will control 50 accumulation zones.
    Air requirements – 20 to 35 psi recommended operating pressure.
    Accumulation zones – 24", 30", or 36" long, air operated. Conveyor frame length changes with zone lengths.
    Filter/Regulator – Supplied loose for mounting to conveyor side frame.
    Guard rails – 1 1/2" x 1 1/2" x 12 gauge galvanized guard rails - both sides.
    Floor supports – Adjustable 31 1/2" to 45 1/2" from floor to top of roller. One support supplied at each end of conveyor and at each bed joint.
    Drive – 2 foot module with motor and reducer.
    Drive shaft – 1" diameter steel shaft, driven by motor and reducer, runs full length of conveyor. Chain coupling supplied at bed joints to couple sections together.
    Drive spools – Delrin spools on drive shaft supply driving power to tread rollers.
    Drive shaft bearings – Sealed, pre-lubricated, self aligning, precision ball bearings on drive shaft.
    Speed reducer – C-face mounted heavy duty worm gear reducer.
    Drive guard – Expanded metal guard full length of conveyor covers drive shaft and other moving drive components.

  • A/C250 Sprocket & Tire Driven Accumulation Conveyor

    The A/C250 accumulation conveyor incorporates chain driven urethane traction wheels with molded Delrin sprocket to drive carrying rollers. It offers true zero-pressure accumulation and versatility – controlled discharge zones, optional release modes, and dual sensor arrangements.

    Features
    True zero-pressure accumulation.
    No fine tuning required.
    3” carrying roller spacing.
    30” long accumulation zones.
    Pre-engineered and assembled.
    Low maintenance.
    Self adjusting elements.
    Powder coat finish.
    Optional power take-off (pto) to slave drive t/c250 curves and junctions.
    Optional light load sensors.


    Specifications and Data
    Frame – 5-1/2” x 1-1/4” x 10 gauge formed steel channel. Powder coat grey finish.
    Carrying Rollers – 1.9” diameter x 16 gauge, galvanized rollers on 3” centers.
    Sensor Rollers – Aluminum rollers with grease packed bearings, pivotally mounted at 30” centers.
    Clutch – Precision molded sprocket and urethane tread mounted on channel frame, four in each accumulation zone.
    Drive Chain – No. 40 roller chain.
    Bed Widths – 16”, 22”, 28”, 34”, and 40” between frames.
    Bed Lengths – Available from 12’-0” minimum to 150’-0” maximum in 30” increments.
    Capacity – 100 pounds per foot.
    Drive – End type located at discharge end of conveyor with automatic chain tensioner. Sprocket keyed to 1-7/16” diameter
    Steel shaft mounted in grease packed-for-life bearings.
    Take-Up – Manually adjustable screw type at infeed end.
    Power Unit – From 1/3 to 3 HP TEFC, C-FACE motor/reducer units. Side mounted units available for low elevation.
    Speeds – 45, 60, 75, 90, 120, 150, and 180 feet per minute.
    Power Take-Off Units – Chain drive components (1:1 speed ratio) and end terminal connection to adjoining “upstream” powered belt, A/C, and T/C conveyors.
    Operating Air Pressure – 5-10 PSI. An air filter/regulator is furnished with each conveyor.
    Operational Release Modes – Singulation, Slug, and Auto-Slug.

  • Accuglide Chain and Pad Driven Accumulation Conveyor

    The Accuglide powered roller conveyor provides quiet, positive transportation and zero-pressure accumulation of cartons, totes, etc. in accumulation lines that may include both straight and curve sections. Accuglide is available with operational modes that allow for maximum output at the lowest possible speed, and integrates 24-volt photo-eye sensors with zone control modules to optimize product detection and flow.

    The integration of 24-volt photo-eye sensors and zone control modules into Accuglide’s design provides the following benefits:

    • Easy zone control/power connections
    • Quick and easy conveyor release mode configuration
    • Sections delivered ready to install and run (sensors/control modules)
    • Micro connector power/communication connections
    • Safe low-voltage power supply requirements
    • Photo-eyes factory installed and aligned
    • Release rates available up to 95 %
    • Acceptance rates up to 100 %
    • Quiet non-contacting sensors
    • No product minimum weight limitation
    • Product minimum height 25 mm (1 in)

    Simple, efficient roller chain (RC50 w/extended pins) and urethane driver pad are pneumatically raised to engage and power the carrier rollers. They are lowered to disengage power from the rollers when sensors detect the presence of product within the next downstream zone.

  • Chain Driven Accumulation Conveyor

    • Medium weight pallets
    • Drum filling operations
    • Large carton accumulation
    • Handles product on slip sheets
    • Photo eye controlled

    Bed – Conveying surface width 14", 16", 18", 24", 28", and 34". 5 1/2" x 1 1/2" x 10 gauge powder painted formed steel channel both sides. Sections are bolted together with butt couplings and floor supports.
    Tread rollers – 2" diameter x 12 gauge steel rollers with #40 sprockets welded to roller tube, 7/16" hex shaft. Rollers spaced on 4", or 6" centers, set low 1 1/2". Roller to roller driven.
    Drive – Located near center of conveyor length, under conveyor frame.
    Drive chain – RC #40 for roller to roller connections, RC #50 chain drive for each zone. Chains are totally enclosed by metal guards.
    Floor supports – 28" to 42" adjustable from floor to top of rollers. One support supplied at each end of conveyor and at each bed joint.
    Accumulation zones – Standard zone lengths are 24", 30", and 36" with a maximum of 30 zones per drive. Conveyor frame lengths change with zone lengths and zone length must be divisible by roller centers. Each zone is driven by an air clutch and controlled by a photo eye sensor.
    Sensing device – NEMA 1 photo electric sensor in each zone detects product presence and activates accumulation feature in trailing zone if upstream zone is occupied.
    Power supply – 120 VAC power supply controls accumulation feature with 24 VDC output. Power supply will control 50 accumulation zones.
    Air requirements – 30 PSI minimum.
    Filter/Regulator – Mounted to conveyor side frame. 50 PSI recommended operating pressure with free air consumption of .001 cu. ft. per sensor operation.
    Capacity – 250 pounds per foot; maximum unit load 1000 lbs. Not to exceed Load capacity.