• Medium Duty Slider Bed Conveyor

    • Packing
    • Inspecting
    • Sorting
    • Assembling
    • Testing
    • Transporting

  • Incline/Decline Slider Bed Belt Conveyor

    • Booster conveyor for gravity flow systems
    • Transporting between floors
    • Center drive

    Belt – Rough-top belt.
    Bed – 12 gauge powder painted formed steel slider bed. Bed is 6 1/2" deep x 6 feet, 8 feet or 10 feet long spliced together with splice plates.
    Under-trussed bed – Extra reinforcement to prevent sag in longer bed sections in addition to reinforcing angles, 24 feet and longer.
    Double nose-over – Two 16" long adjustable bed sections provide a two step transition from incline to horizontal with 15° to 35° adjustment.
    Tail pulley – 4" diameter, crowned with 1 3/16" diameter shaft through 30" wide belt. 6" diameter tail pulley with 1 7/16" diameter shaft turned down on ends for wider than 30" belt.
    Drive pulley – 8" diameter crowned and lagged. 1 7/16" diameter.
    Snub roller – 2 1/2" diameter at drive pulley and 2" diameter at tail pulley.
    Return idlers – 1.9" diameter, adjustable.
    Take-up – Located in center drive assembly, provides 24" of belt take-up.
    Pop-out roller – Free floating, 1 3/8" diameter rollers located at tail pulleys with gravity connector rods. Roller will lift out if anything is caught between pulleys and rollers.
    Floor supports – Adjustable stands to give 31" to 45" height at each end with knee braces.
    Bearings – Sealed prelubricated with cast iron housings.
    Speed reducer – C-face mounted heavy duty worm gear reducer.
    Capacity – 100 lbs. per foot maximum. Not to exceed Load capacity.

  • Incline/Decline Roller Bed Belt Conveyor

    • Transporting between floors
    • Booster covneyor for gravity flow systems
    • Heavier loads can be conveyed because of less friction build-up

    Belt – Rough-top belt.
    Bed – Roller bed with 1.9” diameter x 16 gauge galvanized rollers on 6” centers. Rollers mounted in 7" x 1 1/2” x 12 gauge powder painted formed steel channel frames. Frames bolted together with butt couplings.
    Under-trussed bed – Extra reinforcement to prevent sag in longer bed sections in addition to reinforcing angles, 20 feet and longer.
    X-bracing – Supplied on conveyors 40 feet and longer. Used to square bed sections to insure proper product and belt tracking.
    Double nose-over – Adjustable from 0 to 30 degrees.
    Tail pulley – 4" diameter, crowned with 1 3/16" diameter shaft through 30" wide belt. 6" diameter tail pulley with 1 7/16" diameter shaft turned down on ends for wider than 30" belt.
    Drive pulley – 8" diameter crowned and lagged. 1 7/16" diameter.
    Snub roller – 2 1/2" diameter at drive pulley and 2" diameter at tail pulley.
    Return idlers – 1.9" diameter.
    Take-up – Located in center drive assembly, provides 24" of belt take-up.
    Floor supports – Adjustable 31 1/2" to 45 1/2" from floor to top of belt. One support supplied at each end of conveyor and at nose-over, with knee braces.
    Bearings – Sealed prelubricated with cast iron housings.
    Speed reducer – C-face mounted heavy duty worm gear reducer.

  • Low Profile Belt Conveyor

    Designed to convey light weight bulk parts and stampings.

    Ideal for stamping press operations and plastic injection molding applications.

    Frame construction – 12 ga. Formed steel, bolt in beds.
    Belt widths – Effective widths are "BF" - 1" when overhung side skirts are added.
    Load capacity – 10 lbs. per ft., up to 100 lb. max.

    Optional features

    • Stainless steel contruction
    • Side skirts
    • Start/Stop controls
    • Variable speed controller
    • Wired power cords
    • PVC side guides
    • Urethane, neoprene and static conductive belting
    • Top mount, bottom mount and center drives
    • Leg supports
    • Casters

  • Magnetic Belt Conveyor

    • Transport ferrous materials
    • No moving external parts
    • Submersible watertight construction
    • No need to replace belting
    • Permanent magnets
    • Jam free operation

    Designed and Constructed for Years of Smooth, Quiet Operation

    Slider bad – 12 ga. 304 stainless steel
    Magnets – Ceramic no. 8 permanent magnets on 12 1/2" centers (optional spacing on 1 1/4" increments).
    Frame construction – Watertight 11 ga. steel.
    Chain – No. 50 heavy-duty oversized roller chain.
    Drive – Shaft mounted reducer with 3 phase, 230/460 volt motor. Standard options include: 1/4 hp at 25 fpm, 1/2 hp at 50 fpm, 3/4 hp at 80 fpm.

    Optional equipment
    • Rigidized slider beds
    • Discharge chutes
    • Impact plates
    • Start/Stop controls
    • Emergency stops
    • Hoppers & special height sideguides
    • Extra strength rare earth magnets
    • High-temperature oil-filled frames
    • Casters
    • Lifting lugs
    • Special paint
    • High temperature chain guides
    • Leg supports

  • Plastic Belt Conveyors

    • Standard models for shorter lead times
    • Quick response to quotation request
    • Outstandling service department with many years of experince
    • Engineered to promote longer belt life
    • Assembled and tested prior to shipping
    • Custom designs available (including stainless steel)
    • high quality intralox belting - standard
    • Modular frame design
    • Minimize costly down-time with easilly accessible and replaceable belt sections
    • Belts are positively driven to gratly reduce the risk of belt jamming, "walking" or slipping
    Optional features
    • Infeed hoppers
    • Discharge chutes
    • Top covers
    • Metal detector mounting
    • Cooling fan mounting
    • Controls

  • Hinged Steel Belt Conveyors

    • Custom engineering and manufacturing
    • Heavy duty construction
    • 2 1/2 in, 4 in, 6 in and 9 in pitch belts available

  • Portable Belt Conveyor

    • Stamping operations
    • Small parts
    • Portable or permanent
    Belt – 3 ply PVG (Oil resistant PVC) with 1 1/2" high molded cleats on 12" centers.
    Bed – 6 1/2" deep x 12 gauge powder painted formed steel with 3 1/2" high solid guard rails both sides.
    Tail pulley – 4" diameter crowned with 1 3/16" diameter shaft.
    Overhead drive – 10" clearance over belt, standard.
    Drive pulley – 4" diameter crowned and fully lagged with 1 3/16" diameter shaft.
    Belt return – Belt is returned on smooth sheet metal slide.
    Take-up – 6" long screws located at tail pulley to tighten belt.
    Portable supports – Heavy duty pipe support with 4" diameter casters permit easy mobility of conveyor.
    Bearings – Sealed prelubricated with cast iron housings.
    Speed reducer – C-face mounted heavy duty worm gear reducer.
    Capacity – Total distributed live load not to exceed Load capacity.

  • Wire Mesh Belt Conveyor

    • Drying operations
    • Wet or oily products
    • Hot or cold parts from ovens or freezers
    • One direction operation
    Belt – ½” x 1” flat wire belt. Available in widths of 12", 18", 24" and 36".
    Bed – 6-1/2" deep x 12 gauge powder painted formed channel with 1.9” dia. rollers mounted on 6” centers.
    Drive Sprockets – 6” pitch diameter cast iron sprockets machined for 1 3/16” diameter shaft.
    Tail Pulley - 4" diameter with 4” pitch diameter cast iron sprockets on each end of pulley, 1 3/16” diameter shaft.
    Snub Roller – Adjustable 2” diameter roller located directly behind drive sprockets and tail sprockets.
    Return Idlers – 1.9” diameter, adjustable, on 10’-0” centers.
    Take-Up - 6" long screws located at tail pulley to tighten belt.
    Bearings - Sealed and pre-lubricated with heavy duty housing.
    Floor Supports – Adjustable 31” to 45” from floor to top of belt.
    Speed Reducer - C-Face mounted heavy duty worm gear reducer.
    Motor - 1/2 HP 230/460-3-60 TE motor.
    Belt Speed - 60 FPM constant.
    Capacity – Maximum load per linear foot of conveyor – 75 pounds.
    Various options are available. Contact us for more information.