• 251/267 Chain Driven Live Roller Conveyor

    • Oily conditions
    • Pallets
    • Drums
    • Positive drive

    Bed – 2 1/2" diameter x 11 gauge and 2 5/8" x 7 gauge steel tread rollers, 11/16" hex shafts. No. 50 chain is used on 5", 7 1/2", 10" roller centers only. No. 60 chain is used on 6", 7 1/2", and 12" centers only. Tread rollers mounted in 4" and 6" x 4 gauge powder painted formed steel channel frame. Sections are bolted together with butt couplings and floor supports.
    Drive chain – No. 50 roller chain or No. 60 roller chain can be used with either the 251CRR or 267CRR as above.
    Floor supports – Heavy duty supports are adjustable 30 1/4" to 40" from floor to top of roller. One support at every bed joint and each end of conveyor.
    Center drive – Mounted underneath conveyor, center of section. Can be placed most anywhere in conveyor length.
    Bearings – Sealed, prelubricated ball bearings.
    Chain guard – Lower chain guard is mounted on bottom of roller frame, and upper chain guard is mounted above roller frame to totally enclose drive chain.
    Speed reducer – C-face mounted heavy duty worm gear reducer.
    Capacity – Maximum load per linear foot of conveyor; 300 lbs. with supports on 10' centers, 1000 lbs. with supports on 5' 0" centers.

    Available Options
    - Side Mounted Drive: Motor/Reducer unit can be mounted to side of conveyor frame for lower elevations. Drive is higher than conveyor frame.
    - Conveyor Speed: 30 feet per minute is standard. Other constant, and variable, speeds are available.
    - Rollers Set Low: Rollers can be set low in conveyor frame to provide a guard rail effect.

  • Chain Driven Live Roller Conveyor - 3 CTRS

    • Ideal for slip sheet applications
    • 3" roller centers
    • Handles pallets the "Hard Way"
    • 4000 lb capacity

    Bed – Heavy Duty 4" and 4 3/4" deep x 4 gauge powder painted formed steel channel frame with heavy duty cross braces. Frames are bolted together with butt couplings and floor supports.
    Rollers – 2 1/2" diameter x 11 gauge steel rollers, grease packed and labyrinth sealed bearing, 11/16" hex shaft. Rollers are spaced on 3" centers and set 1/4" high on side rail opposite chain drive.
    Drive chain – RC40 chain is used for roller connections.
    Floor supports – Heavy duty supports are adjustable 24 1/2" to 34" from floor to top of roller. One support at every bed joint and end of conveyor. Formed angle knee braces are supplied for each support.
    Center drive – Mounted underneath conveyor near center of conveyor length. Minimum elevation with standard drive mounting is 18" to top of roller.
    Bearings – Sealed and prelubricated ball bearings.
    Chain guard – Chain guard is on one side only, extends 7/8" above top of rollers. Lower chain guard is mounted on bottom of conveyor frame. Upper chain guard is mounted to top of conveyor frame to totally enclose drive chains.
    Speed reducer – Heavy duty, sealed worm gear reducer.
    Maximum conveyor length – Maximum conveyor length with one drive not to exceed 40 feet.

    Available Options
    - Side Mounted Drive: Motor/Reducer unit can be mounted to side of conveyor frame for lower elevations. Drive is higher than conveyor frame.
    - Conveyor Speed: 30 feet per minute is standard. Other constant, and variable, speeds are available.
    - Rollers Set Low: Rollers can be set low in conveyor frame to provide a guard rail effect.

  • Chain Driven Live Roller Curve

    • Oily conditions
    • Pallets
    • Drums
    • Positive drive


    Bed – 2 1/2" diameter x 11 gauge steel tread rollers, 11/16" hex shaft. Tread rollers mounted in 4" and 6" x 4 gauge powder painted formed steel channel frame. Sections are bolted together with butt couplings and floor supports.
    Drive chain – No. 50 circular roller chain.
    Floor supports – Heavy duty supports are adjustable 30 1/4" to 40" from floor to top of roller. One support at each end of conveyor and one center leg with knee brace.
    Center drive – Mounted underneath conveyor.
    Bearings – Sealed, prelubricated ball bearings.
    Chain guard – Lower chain guard is mounted on bottom of roller frame, and upper chain guard is mounted above roller frame to totally enclose drive chain.
    Speed reducer – Heavy duty worm gear C-face mounted.

    Available Options
    - Side Mounted Drive: Motor/Reducer unit can be mounted to side of conveyor frame for lower elevations. Drive is higher than conveyor frame.
    - Conveyor Speed: 30 feet per minute is standard. Other constant, and variable, speeds are available.
    - Rollers Set Low: Rollers can be set low in conveyor frame to provide a guard rail effect.

  • Heavy Duty Chain Driven Live Roller

    • Heavy duty conveying
    • Positive drive
    • Pallets
    • Heavy drums
    • Reversible drums


    Bed – 6" x 8.2 lb. and 8" x 11.5 lb. powder painted structural channel frame with powder painted structural channel cross braces in each section. Sections are 5 feet long and bolted together with butt couplings and floor supports.
    Tread rollers – 3 1/2" diameter x .30 wall steel tread rollers spaced on 6" or 12" centers, No. 80 sprockets, 1 1/16" hex shaft.
    Drive chain – No. 80 roller chain.
    Floor supports – Heavy duty structural supports are fixed at 18" elevation from floor to top of roller. One support at each end of conveyor and at each bed joint.
    Center drive – Mounted below conveyor bed section. Can be placed most anywhere in conveyor length.
    Bearings – Removable, sealed, prelubricated ball bearings.
    Chain guard – Lower chain guard is mounted on bottom of roller frame, and upper chain guard is mounted above roller frame to totally enclose drive chain.
    Speed reducer – C-face mounted heavy duty worm gear reducer.
    Capacity – Not to exceed Load capacity.

    Available Options
    - Side Mounted Drive: Motor/Reducer unit can be mounted to side of conveyor frame for lower elevations. Drive is higher than conveyor frame.
    - Conveyor Speed: 30 feet per minute is standard. Other constant, and variable, speeds are available.
    - Rollers Set Low: Rollers can be set low in conveyor frame to provide a guard rail effect.