• Medium Duty Slider Bed Conveyor

    • Packing
    • Inspecting
    • Sorting
    • Assembly
    • Testing
    • Transporting

    Bed – 12 gauge powder painted formed steel, 4" deep. Bed sections are 5 feet and 10 feet long, bolted together with spice plates and floor supports.
    Tail pulley – 4" diameter crowned with 1 3/16" diameter shaft.
    Drive pulley – 4" diameter and 8" diameter crowned and fully lagged 4" diameter pulley with 1 3/16" diameter shaft, 8" diameter pulley with 1 7/16" diameter shaft.
    Snub roller – 2" diameter for 4" diameter drive pulley, 2 1/2" diameter for 8" diameter drive pulley.
    Return roller – 1.9" diameter adjustable on 10' 0" centers.
    Floor supports – Adjustable 28 1/2" to 42 1/2" from floor to top of belt. One support supplied at each end of conveyor and at each bed joint.
    Take-up – 6" long screws located at tail pulley to provide belt tension.
    Bearings – Sealed and pre-lubricated with cast iron housings.
    Speed reducer – C-face mounted heavy duty worm gear reducer.
    Capacity – Maximum load per lineal foot of conveyor - 75 lbs. Not to exceed Load capacity.

  • Heavy Duty Slider Bed Conveyor

    • Packing
    • Inspecting
    • Sorting
    • Assembly
    • Testing
    • Transporting

    Bed – 12 gauge powder painted formed steel, 6 1/2" deep. Bed sections are 5 feet and 10 feet long, bolted together with spice plates and floor supports.
    Tail pulley – 4" diameter for belt widths through 30" wide. 6" diameter for 36" and wider belts. 4" diameter pulley has 1-3/16" diameter shaft, 6" diameter pulley has 1 7/16" diameter shaft turned down on ends to 1-3/16" diameter.
    Drive pulley – 8" diameter crowned and fully lagged with 1 7/16" diameter shaft.
    Snub roller – 2 1/2" diameter directly behind drive pulley; 2" diameter at tail pulley.
    Return roller – 1.9" diameter adjustable on 10' 0" centers.
    Floor supports – Adjustable 31" to 45" from floor to top of belt.
    Take-up – 6" long screws located at tail pulley to provide belt tension.
    Bearings – Sealed and pre-lubricated with cast iron housings.
    Speed reducer – C-face mounted heavy duty worm gear reducer.
    Capacity – Maximum load per lineal foot of conveyor - 100 lbs. Not to exceed Load capacity.

  • Trough Slider Bed Belt Conveyor

    • Conveys boxes, bags, cases and loose parts
    • Built in guard rails allow overhead conveying

    Bed – 12 gauge powder painted formed steel with 2 1/2" high vertical sides bolted to top of bed. Standard sections are 5 and 10 feet long bolted together with floor supports and splice plates.
    Tail pulley – 4" diameter crowned with 1 3/16" diameter shaft.
    Drive pulley – 4" diameter and 8" diameter crowned and fully lagged. 4" diameter pulley with 1 3/16" diameter shaft, 8" diameter pulley with 1 7/16" diameter shaft.
    Snub-roller – 2" diameter for 4" diameter pulley, 2 1/2" diameter for 8" diameter pulley.
    Return idler – 1.9" diameter adjustable, on 10' 0" centers.
    Floor supports – Adjustable 28 1/2" to 42 1/2" from floor to top of belt. One support supplied at each end of conveyor and at each bed joint.
    Take-up – 6" long screws located at tail pulley to provide belt tension.
    Bearings – Sealed-prelubricated with cast iron housings.
    Speed reducer – C-face mounted heavy duty worm gear reducer.
    Capacity – Maximum load per lineal foot of conveyor - 75 pounds. Not to exceed Load capacity.

  • Slider Bed Trash Conveyor

    • Adjustable floor supports
    • Inclie to 15 degrees
    • Guard rails

    Bed – 5 1/2" deep x 14 gauge powder painted formed steel channel frame. Bed sections are 10 feet and 5 feet long, bolted together with splice plates and floor supports.
    Belt – FS top side, brushed bottom side, with clipper lacing.
    Guard rail – 6" high x 16 gauge formed, powder painted steel on both sides, full length of bed sections.
    Underside guards – Formed 16 gauge pans full length of bed sections, removable, secured with TEK screws.
    Tail pulley – 4" or 6" diameter (see chart) crowned with 1 3/16" diameter shaft.
    Drive pulley – 4", 6" and 8" diameter crowned and fully lagged. 4" and 6" diameter pulleys have 1 3/16" diameter shaft, 8" diameter pulley has 1 7/16" diameter shaft.
    Snub-roller – 2" diameter for 4" and 6"diameter pulleys, 2 1/2" diameter for 8" diameter pulley.
    Return rollers – 1.9" diameter placed on 10' centers.
    Floor supports – Adjustable 30" to 44" from floor to top of belt. One floor support provided at each end of conveyor and at each bed joint.
    Take-up – 6" long screws located at tail pulley to provide belt tension.
    Bearings – Sealed, prelubricated with cast iron housings.
    Speed reducer – C-face mounted heavy duty worm gear reducer.
    Capacity – 10 pounds per foot maximum live load. See load Capacity.

  • Roller Bed Belt Conveyor

    • Packing
    • Inspecting
    • Sorting
    • Assembling
    • Testing
    • Transporting horizontally or on incline

    Bed – Roller bed with 1.9" diameter galvanized steel rollers. Rollers spaced on 6" centers. Rollers mounted in 7" deep x 12 gauge powder painted formed steel channel frames. Frames bolted together with butt couplings and floor supports.
    X-Bracing – Frame squaring device supplied on conveyors 40 feet and longer for every other bed section. X-bracing insures good product and belt tracking.
    Drive pulley – 8" diameter crowned and fully lagged, 1 7/16" shaft.
    Tail pulley – 4" diameter crowned supplied through 30" wide belts. 6" diameter crowned supplied for 36" and wider belts. 4" diameter pulley has 1 3/16" diameter shaft; 6" diameter pulley has 1 7/16" diameter shaft turned down on ends to 1 3/16" diameter.
    Pop-out roller – 1.9" diameter roller, Iocated at drive pulley and tail pulley.
    Snub roller – 2 1/2" diameter adjustable roller, Iocated directly behind drive pulley, 2" diameter located behind tail pulley.
    Return rollers – 1.9" diameter adjustable on 10' 0" centers.
    Take-up – Located at tail end, provides 12" of belt take-up.
    Bearings – Sealed-prelubricated with cast iron housings.
    Floor supports – Adjustable 31 1/2" to 45 1/2" from floor to top of belt. One support supplied at each end of conveyor and at each bed joint.
    Speed reducer – C-face mounted heavy duty worm gear reducer.
    Capacity - 200 pounds per foot maximum. Not to exceed Load capacity.