• Flat Belt Driven Live Roller Conveyor

    • Accumulates tote pans, cartons, boxes etc.
    • Minimum back pressure
    Bed – 7" x 1 1/2" x 12 gauge powder painted formed steel channel frame, bolted together with butt couplings and floor supports.
    Tread rollers – 1.9" diameter x 16 gauge galvanized steel rollers spaced on 2 1/4", 3", 4 1/2" or 6" centers. Safety pop-out design prevents damage to product or harm to personnel if caught between belt and tread rollers.
    Pressure rollers – 1.9" diameter x 16 gauge galvanized steel rolled spaced on 6:, 9",= or 12: centers, cam adjusted.
    X-bracing – Frame squaring device supplied on conveyors 40 feet and longer on every other bed section. X-bracing insures good product and belt tracking.
    Tail pulley – 4" diameter crowned with 1 3/16" shaft.
    Snub roller – 2 1/2" diameter adjustable, located directly behind drive pulley. 2" diameter at each end directly behind terminal pulleys.
    Return idlers – 1.9" diameter adjustable on 10' 0" centers.
    Floor supports – 31 1/2" to 45 1/2" adjustable from floor to top of rollers. One support supplied at each end of conveyor and at each bed joint.
    Take-Up – Located in center drive, provides 24" of belt take-up.
    Bearings – Sealed and pre-lubricated with cast iron housings.
    Speed reducer – C-face mounted heavy duty worm gear reducer.

  • V-Belt Driven Live Roller Curves

    • Transports around turns with positive alignment of package
    • Can be slave driven from Flat Belt Driven Live Roller Conveyor
    Driving belt – "B" section V-belt.
    Bed – 2 1/2" diameter tapered to 1 11/16" diameter x 14 gauge wall plated tread rollers. 7/16" hex shafts. Steel pressure sheaves. Mounted in 7" x 1 1/2" x 12 gauge powder painted formed steel channel frame.
    Floor supports – Adjustable 31 1/2" to 45 1/2" from floor to top of rollers. One support at each end, and center leg on outer rail.
    Take-up – Screw take-up provided to insure proper V-belt tension. Mounted underneath conveyor.
    Tangent – 12" long, one on each end.
    End Drive – Mounted below bed section.
    Bearings – Sealed prelubricated with cast iron housings.
    Speed reducer – C-face mounted heavy duty worm gear reducer.

  • V-Belt Driven Live Roller Spurs

    • Diverging or converging applications
    • Positive alignment of package
    • Right and Left Hand Units Available
    Driving Belt - "B" section V-belt.
    Bed - Roller bed width between rails 15", 21", 27", 33" and 39". 7-1/2" x 1-1/2" x 12 gauge powder painted formed steel channel frame.
    Tread Rollers - 2-1/2" diameter tapered to 1-11/16" diameter plated and 1.9" diameter x 16 gauge plated steel tread rollers, 7/16" hex shaft.
    Pressure Sheaves - 3" diameter x 3/8" bore, adjustable to give required driving force.
    Take-Up - Screw take-up provided to insure proper V-belt tension. Mounted underneath conveyor.
    Tangent - 12" long, on one end of curved spur.
    Floor Supports - Adjustable 31-1/2" to 45-1/2" from floor to top of rollers.
    End Drive - Mounted below bed section.
    Bearings - Sealed prelubricated with cast iron housings.
    Speed Reducer - C-Face mounted heavy duty worm gear reducer.
    Motor - 1/2 HP 230/460-3-60 TE motor.
    Belt Speed - 60 FPM constant.
    Capacity - 540 Ibs. total distributed live load.

  • Line Shaft Driven Live Roller Conveyor

    • Low pressure accumulation
    • Clean room installation
    • Economical transportation conveyor
    • Assembly conveyor


    Driving belts – 3/16" diameter round urethane "O" rings from drive shaft to tread rollers.
    Bed – 7" x 1 1/2" x 12 gauge powder painted formed steel channel frame with heavy duty cross braces and splice plates.
    Rollers – 1.9" diameter x 16 gauge galvanized steel tread rollers with 7/16" hex shaft and sealed, greased for life bearings, spaced on 3" centers.
    Floor supports – Adjustable 31 1/2" to 45 1/2" from floor to top of tread roller. One support supplied at each end of conveyor and at each bed joint.
    Drive – 2 foot module with motor and reducer. Drive module will be bolted to intermediate section.
    Drive shaft – 1" diameter steel shaft, driven by motor and reducer, runs full length of conveyor. Chain coupling supplied at bed joints to couple sections together.
    Drive spools – Delrin spools located on drive shaft supplies driving power to tread rollers.
    Drive shaft bearings – Sealed, prelubricated, self aligning, precision ball bearings on drive shaft.
    Speed reducer – C-face mounted, heavy duty worm gear reducer.
    Drive guard – Perforated metal guard full length of conveyor covers drive shaft and other moving drive components.

    Note: For Total load capacities 2600, 5400 and 7200 lb – Capacities based on 3" roller centers with all rollers driven. Rollers limited to 15 lb maximum live load per roller.

  • Line Shaft Driven Live Roller Curve

    Bed – Roller bed with 2 1/2" diameter tapered to 1 11/16" diameter x 14 gauge galvanized and 1.9" diameter x 16 gauge galvanized tread rollers. Mounted in 7" x 12 gauge powder painted formed steel channel frame.
    Floor supports – Adjustable 31 1/2" to 45 1/2" from floor to top of rollers. One support at ends of 190LSC (Curve), 190LSCS (Curve Spur) and 190LSS (Straight Spur). Single leg supplied for center of outside rail on 90° 190LSC only.
    Slave driven – Curves or spurs are slave driven from drive shaft of Model 190LS conveyor. Shafts are coupled by chain coupling at bed joints.
    Drive Shaft – 1" diameter steel shaft extends full length of conveyor, coupled with universal joints ("U" joints) at necessary intervals.
    Drive spools – 2" diameter Delrin spool held in place on drive shaft with "snap-on" lock collars.
    Drive guard – Underside of drive shaft with spools and drive belts guarded full length of conveyor.
    Drive belts – 3/16" diameter urethane belt from drive spool to tread roller.
    Bearings – Tread rollers, pre-lubricated ball bearings. Sealed, prelubricated, self-aligning ball bearings on drive shaft.
    Butt couplings – Standard for connecting to 190LS.

  • Line Shaft Driven Live Roller Spurs

    Bed - Roller bed with 2-1/2" diameter tapered to 1-11/16" diameter x 14 gauge galvanized and 1.9" diameter x 16 gauge galvanized tread rollers. Mounted in 7" x 12 gauge powder painted formed steel channel frame.
    Floor Supports - Adjustable 31-1/2" to 45-1/2" from floor to top of rollers. One support at ends of 190LSC (Curve), 190LSCS (Curve Spur) and 190LSS (Straight Spur). Single leg supplied for center of outside rail on 90° 190LSC only.
    Slave Driven - Curves or spurs are slave driven from drive shaft of Model 190LS conveyor. Shafts are coupled by chain coupling at bed joints.
    Drive Shaft - 1" diameter steel shaft extends full length of conveyor, coupled with universal joints ("U" joints) at necessary intervals.
    Drive Spools - 2" diameter Delrin spool held in place on drive shaft with "snap-on" lock collars.
    Drive Guard - Underside of drive shaft with spools and drive belts guarded full length of conveyor.
    Drive Belts - 3/16" diameter urethane belt from drive spool to tread roller.
    Bearings - Tread rollers, pre-lubricated ball bearings. Sealed, prelubricated, self-aligning ball bearings on drive shaft.
    Butt Couplings - Standard for connecting to 190LS.

  • Sprocket & Tire Driven Live Roller Conveyor

    T/C250 conveyors incorporate chain driven urethane traction wheels with molded Delrin sprocket to drive carrying rollers.
    In addition to straight conveyor, T/C250 live roller conveyor is available in 21 various configurations of curves and spurs.

    Features
    Economical – Pre-engineered components are low cost, easy to install and maintain.
    No Critical Adjustments Necessary – Exclusive, chain driven traction wheels transmit power directly to carrying rollers.
    Unusually Quiet, Safe Operation – The enclosed non-metallic drive mechanisms and concentric drive element minimize vibration noise and wear.
    Versatile – Handles a wide range of product sizes and weights up to 100 pounds per foot.

    Specifications and Data
    Frame – 5” x 1-1/4” x 10 gauge formed steel channel with all drive components fully enclosed by segmented guards.
    Extruded UHMW polyethylene chain guide supports both drive and return runs of chain. Powder coat grey finish.
    Carrying Rollers – 1.9” diameter x 16 gauge, galvanized rollers on 3” centers.
    Traction Wheel – Molded sprocket with urethane tread is mounted in fixed position on channel frame rail.
    Drive Chain – No. 40 roller chain.
    Bed Widths – 16”, 22”, 28”, 34”, and 40” between frames.
    Bed Lengths – Available from 4’-0” minimum to 150’-0” maximum in 1” increments.
    Capacity – 100 pounds per foot.
    Drive Units – Drive sprocket (RC40, 35 tooth) is keyed to 1-7/16” diameter drive shaft. Effective chain pull is 500lbs.
    Available in end type drives located at discharge end of conveyor.
    Power Unit – From 1/3 to 3 HP TEFC, C-FACE motor/reducer units. Side mounted units available for low elevations.
    Speeds – 45, 60, 75, 90, 120, 150, and 180 feet per minute.
    Power Take-Off Units – Chain drive components (1:1 speed ratio) and end terminal connection to adjoining “upstream” powered belt, A/C, and T/C conveyors.

  • Chain Driven Live Roller Conveyor

    • Wash down operations
    • Oily conditions
    • Positive drive – no belt slippage

    Drive Chain – No. 40 roller chain on straight sections.
    Bed – 3 1/2" x 1 1/2" x 10 gauge powder painted formed steel channel on one side, 5" x 1 1/2" x 10 gauge formed steel channel on chain drive side. Sections are bolted together with butt couplings and floor supports.
    Tread rollers – 2" diameter x 12 gauge steel with #40 sprockets welded to roller tube, 7/16" hex shafts. Rollers spaced on 4", 6", 8" and 12" centers. Rollers are roller to roller driven.
    Chain guard – Chain guard is mounted to frame to totally enclose drive chain.
    Center drive – Mounted underneath conveyor, near center of section. Can be placed most anywhere in conveyor length. Specify.
    Floor supports – Adjustable 28" to 42" from floor to top of rollers. One support supplied at each end of conveyor and at each bed joint.
    Speed reducer – C-face mounted heavy duty worm gear reducer
    Capacity – Maximum load 150 Ibs. per foot; maximum unit load 500 pounds. Not to exceed Load capacity.